Hosted by IDTechEx
Off Grid Energy Independence
Posted on November 27, 2020 by  &  with 1 Comment

An Ultrafast Way to Produce Stable Perovskite Cells

Most solar cells today are made with refined silicon that turns sunlight into clean electricity. Unfortunately, the process of refining silicon is far from clean, requiring vast amounts of energy from carbon-emitting power plants. For a greener alternative to silicon, researchers have focused on thin-film perovskites - low-cost, flexible solar cells that can be produced with minimal energy and virtually no CO2 emissions. While perovskite solar cells are promising, significant challenges need to be addressed before they can become commonplace, not least of which is their inherent instability, which makes manufacturing them at scale difficult.
 
"Perovskite solar technology is at a crossroads between commercialization and flimflammery," said Stanford University postdoctoral scholar Nick Rolston. "Millions of dollars are being poured into startups. But I strongly believe that in the next three years, if there isn't a breakthrough that extends cell lifetimes, that money will start to dry up."
 
That's why a new perovskite manufacturing process developed at Stanford is so exciting, Rolston said. In a new study, published in the Nov. 25 issue of the journal Joule, he and his colleagues demonstrate an ultrafast way to produce stable perovskite cells and assemble them into solar modules that could power devices, buildings and even the electricity grid. For further information see the IDTechEx report on Materials for Printed/Flexible Electronics 2021-2031: Technologies, Applications, Market Forecasts.
 
 
"This work provides a new milestone for perovskite manufacturing," said study senior author Reinhold Dauskardt, the Ruth G. and William K. Bowes Professor in the Stanford School of Engineering. "It resolves some of the most formidable barriers to module-scale manufacturing that the community has been dealing with for years."
 
Fingernail-size samples
Perovskite solar cells are thin films of synthetic crystalline made from cheap, abundant chemicals like iodine, carbon and lead. Thin-film cells are lightweight, bendable and can be grown in open-air laboratories at temperatures near the boiling point of water, a far cry from the 3,000-degree Fahrenheit (1,650-degree Celsius) furnaces needed to refine industrial silicon. Scientists have developed perovskite cells that convert 25 percent of sunlight to electricity, a conversion efficiency comparable to silicon. But these experimental cells are unlikely to be installed on rooftops anytime soon.
 
"Most work done on perovskites involves really tiny areas of active, usable solar cell. They're typically a fraction of the size of your pinky fingernail," said Rolston, who co-lead the study with William Scheideler, a former Stanford postdoctoral scholar now at Dartmouth College.
 
Attempts to make bigger cells have produced defects and pinholes that significantly decrease cell efficiency. And unlike rigid silicon cells, which last 20 to 30 years, thin-film perovskite eventually degrades when exposed to heat and moisture.
 
 
"You can make a small demonstration device in the lab," Dauskardt said. "But conventional perovskite processing isn't scalable for fast, efficient manufacturing."
 
Record-setting processor
To address the challenge of large-scale production, the Dauskardt team deployed a patented technology they recently invented called rapid-spray plasma processing. This technology uses a robotic device with two nozzles to quickly produce thin films of perovskite. One nozzle spray-coats a liquid solution of perovskite chemical precursors onto a pane of glass, while the other releases a burst of highly reactive ionized gas known as plasma.
 
"Conventional processing requires you to bake the perovskite solution for about half an hour," Rolston said. "Our innovation is to use a plasma high-energy source to rapidly convert liquid perovskite into a thin-film solar cell in a single step."
 
Using rapid-spray processing, the Stanford team was able to produce 40 feet (12 meters) of perovskite film per minute - about four times faster than it takes to manufacture a silicon cell.
 
"We achieved the highest throughput of any solar technology," Rolston said. "You can imagine large panels of glass placed on rollers and continuously producing layers of perovskite at speeds never accomplished before."
 
In addition to a record production rate, the newly minted perovskite cells achieved a power conversion efficiency of 18 percent.
 
 
"We want to make this process as applicable and broadly useful as possible," Rolston said. "A plasma treatment system might sound fancy, but it's something you can buy commercially for a very reasonable cost."
 
The Stanford team estimated that their perovskite modules can be manufactured for about 25 cents per square foot - far less than the $2.50 or so per square foot needed to produce a typical silicon module.
 
Solar modules
Silicon solar cells are typically connected together in encapsulated modules to boost their power output and withstand harsh weather conditions. Perovskite manufacturers will eventually have to build stable, efficient modules to be commercially viable. Toward this end, the Stanford team successfully created perovskite modules that continued to operate at 15.5 percent efficiency even after being left on the shelf for five months.
 
Conventional silicon modules produce electricity at a cost of about 5 cents per kilowatt-hour. To compete with silicon, perovskite modules would have to be encapsulated in a weatherproof layer that keeps out moisture for at least a decade. The research team is now exploring new encapsulation technologies and other ways to significantly improve durability.
 
"If we can build a perovskite module that lasts 30 years, we could bring down the cost of electricity below 2 cents per kilowatt-hour," Rolston said. "At that price, we could use perovskites for utility-scale energy production. For example, a 100-megawatt solar farm."
 
 
 
Source and top image: Stanford University
More IDTechEx Journals